Amplifier outputs

• 6 x 110W stereo outputs at @ 8 Ohms
• 2 stereo preamplifier outputs for powered subwoofer, AV Receiver, and secondary power amplifiers
• Expandable to 96 rooms. Each additional unit supports 8 more rooms
• Link two zones, for example, you can link the Living Room zone with a second pre-amplified zone connected to a powered subwoofer
• Configure room for stereo or mono
• EQ settings per room, include: 7-band Parametric Equalizer, Loudness, Balance, Bass and Treble
• Each room includes an additional low-pass filter option (when adding a subwoofer)
• Separate output gain control for each room
• Configurable maximum volume per room
• Configurable power on volume per room
• Configurable audio delay per room

Input Sources

• Sources 1-8: Analog Stereo or Coax Digital Audio (PCM)
• Sources 9-12: Coax or Optical Digital Audio (PCM)
• Sources 1-12: Programmable delay up to 600 ms
• 12 buffered coax digital outputs used to link sources with an additional expansion unit
• 8 x IR emitter ports designed to relay IR signals from a room with a keypad or IR receiver and control a specific source component.
• 2 x IR emitter ports designed to relay all IR signals from a room and control source components common to all zones
• Configurable input gain for input sources, so the output volume level is  matched for all sources

Triggers

• AMP ON 1-8: +12V signal when the associated room is powered on
• +12V signal when any room on this unit is powered on
• 2 Trigger Inputs (PRESETS P1 & P2) can be used to trigger a preset and typically used to integrate a doorbell ringer
• 14 programmable presets available

Keypads

• 8 Keypad ports are available for use with optional keypads 
• IR receiver integrated with keypads
• Configurable source specific IR routing available
• Available in white only

Front Panel Touch Panel Control

• 2.8” color touch panel allows installer to control the matrix amplifier and view the current status during setup and/or maintenance

Network

• Control the matrix amplifier using standard IP network connection
• Select Static or Dynamic IP Address
• 2 Ethernet ports (MAIN IN/EXT OUT) to simplify linking multiple expansion units

Other

• Temperature monitoring and thermal control protection
• 110 / 240VAC 50/60 HZ automatic switch
• Low standby power
• Rack ears included
• Firmware upgradable for maintenance and future functionality

Amplifier Section

• RMS Power @ 8 ohms: 110W x 6 (8 Ohms, all channels driven, 1% THD)
• RMS Power @ 4 ohms: 150W x 6 (4 Ohms, all channels driven, 1% THD)
• THD: <0.1% (100W, 8 Ohm load)
• Speaker Impedance: 4-8 Ohms
• Analog Input Sensitivity (S1-S8): 0.75VRMS (Vol 100, Gain 0dB, 55W Output)
• Analog Input Impedance (S1 – S8): 22KΩ
• Digital input Sensitivity: 0dBFS
• Preamplifier Output Level (Z7 & Z8): +14dB
• Frequency Response - 48 KHz sample rate: 10 Hz – 22 KHz
• Frequency Response - 96 KHz sample rate: 10 Hz – 42 KHz
• Tone Control:  ±12dB, 100 Hz (Bass)
• Tone Control:  ±12dB, 10 KHz (Treble)
• Signal to Noise Ratio: 95dB (IHA-A, 0.75V input / unbalanced)

Interface

• IR Output: Ten 3.5mm Jack: IR1 – IR10 current limited to 25mA.
• Ethernet: 100Base T, MAIN IN and Switch EXT OUT. 
• USB: One USB mini-B 5 pin 
• Controller: Eight RJ45 Socket 
• BUS RUN: One 4 way terminal block (0V, IR, 12V & Data)
• Amp On & PG Control: One 10 way terminal plug with Amp ON 1 – 8 and Two Page preset contact closure inputs: PG1 & PG2

General

• Power Supply: 110 / 240VAC 50/60 HZ
• Power Consumption: 650 W
• Standby Power Consumption: 6W
• Dimensions: 17.13” х 3.54” х 15.35” (435 x 90 x 390 mm)
• Height including feet: 4.13” (105 mm)
• Weight: 15.4lbs (7Kg)
• Warranty: 1 Year

• CasaTunes 12X8 Manual
• ‍QuickStart Guide for CT-12X8MA Matrix Amplifier